F9 E1
Long drain
Drain times longer than expected — typically over eight minutes. Water stays in the drum.
Common causes: clogged drain pump filter, kinked drain hose, or a failing drain pump.
Available now
Maytag Washing Machine Repair in Dammam
Maytag washer showing F9 E1, F8 E1, F5 E2, F7 E1, F51, LdL or LdU, not draining, leaking or not spinning? Our trained technicians specialise in Maytag's Commercial Technology (MCT), DuraCore Direct Drive, PowerWash cycle and Deep Fill systems. Suitable parts.
- Home visits by appointment
- All F#E# codes decoded
Free inspection Calls answered 24/7 Independent repair service
Maytag-specialist technicians · Parts already on the van
Every Maytag Washing Machine Error Code, Decoded
Maytag uses two code systems depending on the machine. Front-load washers report faults as an F#E# letter-number pair. Top-load high-efficiency washers use short words and abbreviations (Sud,Ofb, LdL), plus the same F-and-E pairs for system errors.
F8 E1
LF
Lo FL
LF
Lo FL
Low flow
The washer senses low water flow or takes too long to fill.
Common causes: water supply off, inlet hose kinked or frozen, or a clogged inlet filter.
F5 E2
Door lock error
The door is not locking properly.
Common causes: items blocking the door, door not fully closed, or a failed door lock assembly.
F7 E1
Motor speed sensing error
The motor cannot achieve the correct speed for the cycle.
Common causes: shipping bolts not removed, overloaded washer, or a faulty motor control board.
F8 E2
Dispenser system error
There is a problem with the detergent or softener dispenser system.
Common causes: clogged dispenser, failed dispenser motor, or blocked dispenser path.
F51
Rotor position sensor fault
On Maytag Bravos and Bravos XL models (MVWB, MVWX series), F51 means the main control board has lost track of basket rotation from the rotor-position sensor (RPS).
Cause: intermittent connection at the RPS causing the electronic control to indicate an F51 code.
LdL
Lid not locking
The lid is not locking (top-load models).
Common causes: failed lid lock mechanism or broken lid switch.
LdU
Lid cannot unlock
The lid cannot unlock after the cycle.
Common causes: jammed lid lock mechanism or failed control board.
drn
Not draining
The washer is not draining properly (top-load models).
Common causes: clogged drain pump filter or kinked drain hose.
Sud
Sd
Sd
Excess suds
Too many suds in the washing machine.
Fix: Use HE detergent only. The washer will automatically extend rinse time. Run one empty cycle on the hottest setting with no detergent to clear buildup.
Ofb
Out of balance
The washer load is out of balance.
Fix: Redistribute the load in the drum and press start again.
OL
Overload
The washer load was too large.
Fix: Remove several items and restart the cycle.
HC
Hoses reversed
Hot and cold inlet hoses installed incorrectly (reversed).
Fix: Shut off water and swap the hoses.
lid
Lid open
The washer lid was left open.
Fix: Close the lid firmly.
PF
Power failure
The wash cycle was interrupted by a power failure.
Fix: Hold Start to resume the cycle where it left off.
Int
Paused / cancelled
The cycle was paused or cancelled.
Fix: Press Pause twice, then Power once.
LOC
LC
LC
Control Lock
Control Lock has been activated on the panel.
Fix: Hold the Control Lock button for 3 seconds to unlock.
rL
F34
F34
Items in Clean Washer cycle
Items were detected in the washer during the Clean Washer cycle.
Fix: Remove the items and restart the cycle.
dET
Detergent cartridge
Detergent cartridge not detected in the dispenser (on Optimal Dose models).
Fix: Reseat the cartridge firmly and close the drawer until it clicks.
Didn't find your error code? Call 054 400 6384 — tell us the code and we'll identify the cause in minutes.
We're Trained on Maytag's Advanced Technologies
Maytag's American-engineered washers carry commercial-grade components that demand specialist knowledge — and that's exactly what we have.
Maytag Commercial Technology (MCT)
Maytag's Commercial Technology (MCT) platform brings commercial-grade components to residential washers. From heavy-duty springs and belts to beefed-up motors and frames, MCT washers are engineered for durability. We diagnose and repair MCT-specific drive components, suspension systems and control boards.
DuraCore™ System
Maytag's commercial-grade DuraCore™ System eliminates high-maintenance belts, gears and pulleys in favor of a robust Direct Drive Motor and Base-Mount Suspension, reducing parts by 50%. The DuraCore™ Direct Drive Motor unleashes 900 RPM of speed to power through the toughest loads. We service the direct drive motor, base-mount suspension and related components.
PowerWash® Cycle
Maytag's PowerWash cycle uses a combination of extra cleaning action and heated water to remove everyday tough stains in a single wash. It delivers best-in-class cleaning driven by the PowerWash system. We diagnose and repair heating elements, wash action components and the control board that manages this cycle.
Deep Fill Option
Maytag's Deep Fill option (also called Deep Water Wash on some models) adds extra water to your load, usually filling it to the maximum water level. This helps clean items like towels, jeans and other sturdy or heavily soiled fabrics. We service water inlet valves, pressure sensors and the control board that manages water level selection.
PowerWash® Agitator
Maytag's PowerWash agitator provides robust wash action for tough loads. Combined with the PowerWash cycle, it tackles any size load with extra cleaning action. We repair agitator dogs, drive splines and related components.
Sanitize with Oxi
Maytag's Sanitize with Oxi cycle removes 99.9% of bacteria and eliminates allergens. We service the heating elements, steam generators and control boards that manage this cycle.
Smart Capable / Maytag App
Maytag's Smart Capable washers can be controlled and monitored via the Maytag app. We diagnose and repair connectivity issues, Wi-Fi module faults and control board problems affecting the smart system.
Optimal Dose Dispenser
Maytag's Optimal Dose dispenser automatically releases the right amount of detergent at the right time for optimal cleaning. We repair dispensing pumps, sensors and the auto-dose control board. This is common on MHW8630 models.
Maytag Washer Faults We Fix Every Day
Pick the symptom closest to your situation. Each one links to a dedicated page with detailed causes and repair information.
Won't Drain (F9 E1 / drn)
Standing water after the cycle. Most common cause is a clogged drain-pump filter or coin trap. We clean the filter, check the drain hose and replace the drain pump if needed.
Learn moreWon't Fill (F8 E1 / LF)
Washer won't fill. Check if the tap is open, the inlet hose is kinked or frozen, or the supply filter is clogged. We repair the water inlet valve and pressure switch.
Learn moreWon't Spin
Clothes coming out soaked. On Maytag, won't spin often stops at the transmission. Heavy-duty transmission or shift actuator issues are common culprits. We also diagnose faulty lid switches, broken drive belts and motor couplings.
Learn moreMaking Loud Noises
Banging, grinding or squealing during the spin. Common causes include worn drum bearings, unbalanced loads or worn shock absorbers. A rumble climbing with spin speed or play at the drum rim on MHW front-loaders raises the bearing and tub-seal question.
Learn moreLeaking Water
Water on the laundry room floor. Common causes include a loose supply hose connection, a misaligned drain filter or a worn door seal (door boot mould is common on MHW5630 and MHW6630 front-loaders).
Learn moreExcessive Vibration / Walks
Machine moves during the spin cycle. On top-loaders, heavy vibration and a tub that hits the cabinet usually means the four suspension rods that hang the tub have worn springs. We replace suspension rods, shock absorbers and level the machine.
Learn moreWon't Turn On
No power at all. We check the power supply, control board and door lock mechanism.
Learn moreStops Mid-Cycle
A cycle stalling at drain, a spin that never reaches speed, or a door that will not unlock. Maytag uses the same F#E# code system as every Whirlpool Corporation brand. We diagnose the drain pump, filter, door lock assembly, pressure switch and motor control in that order.
Learn moreBad Smell
Musty odours. We clean and replace mouldy door gaskets and address drainage issues causing bacteria buildup. Common on front-load models. We recommend regular Clean Washer cycles with affresh tablets.
Learn moreEvery Maytag Series and Model
We service every Maytag washer family sold in the region — from the entry-level MVW4505 to the premium MHW8630 front-loader.
- MHW5630
- MHW6630
- MHW8630
- MVW4505
- MVW5430
- MVW6230
- MVWB765
- MVWB955
- Bravos
- Bravos XL
- Bravos MCT
- MVWX Series
Model not listed? Call us — we repair every Maytag washing machine sold in Saudi Arabia.
Why Choose Us
Why Maytag Owners in Dammam, Al Khobar and Dhahran Trust Us
Because Maytag is American-engineered with Commercial Technology (MCT), DuraCore Direct Drive and PowerWash systems. We've been working on them daily.
-
Maytag-trained techniciansSpecific expertise in Commercial Technology (MCT), DuraCore™ and PowerWash systems.
-
Common Maytag parts on every vanDrain pumps, door locks, inlet valves, suspension rods.
-
Free inspectionWe diagnose the fault at your home and explain the fix.
-
Warranty-backed repairs
-
Calls 24/7 · Visits Sat–Thu 8 AM–11 PM, Fri 2 PM–11 PMBecause a Maytag washer never breaks at a convenient time.
Four Simple Steps to a Working Maytag Washer
No waiting rooms, no hauling your machine across town, no surprise invoices.
Call or Book Online
Tell us your Maytag model and the error code or symptom you're seeing.
Our Maytag-trained technician inspects the washer at your home and gives you before starting any work.
Repair Completed On-Site
Most repairs are completed on the spot with suitable Maytag parts — drain pumps, door locks, control boards and MCT components.
Your Satisfaction
Maytag Repair Near You
Our technicians cover Dammam, Al Khobar and Dhahran.
- Dammam
- Al Khobar
- Dhahran
Maytag Washing Machine Repair — Common Questions
Everything customers in Dammam ask us before booking a Maytag repair.
What does error code F9 E1 mean on a Maytag washer?
Error F9 E1 means the drain time is longer than expected — typically over eight minutes. Common causes: clogged drain pump filter, kinked drain hose, or a failing drain pump. See all Maytag error codes.
What does error code F8 E1 or LF mean on a Maytag washer?
F8 E1 / LF / Lo FL means the washer senses low water flow or takes too long to fill. Check that household water supply is on and both valves are fully open. Inlet hoses should not be kinked or frozen.
What does error code F5 E2 mean on a Maytag washer?
Error F5 E2 means the door is not locking properly. Check that nothing is blocking the door and it is fully closed. The door lock assembly may need replacement.
What does error code F51 mean on a Maytag Bravos?
On Maytag Bravos and Bravos XL models (MVWB, MVWX series), F51 means the main control board has lost track of basket rotation from the rotor-position sensor (RPS). This is an intermittent connection at the RPS causing the electronic control to indicate an F51 code.
What do the Maytag word codes Sud, Ofb, OL, HC mean?
These are user-clearable codes. Sud = excess suds, use HE detergent only. Ofb = out of balance, redistribute the load. OL = overload, remove several items. HC = hot and cold inlet hoses reversed — swap them.
Can you fix Maytag PowerWash cycle issues?
Yes. PowerWash issues typically come from the heating element, the wash action components, or the control board that manages the cycle. We diagnose and replace the exact failed component with suitable Maytag parts.
Do you repair all Maytag washer models?
Yes. We repair every Maytag model: MHW5630, MHW6630, MHW8630 front-loads; MVW4505, MVW5430, MVW6230, MVWB765/955 top-loads; and Bravos / Bravos XL / Bravos MCT series.
Book a Maytag Repair
Maytag Washer Broken? Don't Wait — Call Now.
Free diagnosis.
- Specialists in MCT, DuraCore & PowerWash
- Warranty-backed repairs
Call us 24/7
054 400 6384