Calls answered 24/7
Whirlpool washer not draining, not filling, not spinning, or showing an error code? Our Whirlpool-trained technicians arrive with Suitable parts fix it on the same visit — 6th Sense, SenseInverter, FreshCare+ Steam, Load & Go™, all models.
Free inspection Calls answered 24/7 Independent repair service
Whirlpool uses two code systems depending on the machine. Some codes point at a specific part and need a technician. Here are both.
F-and-E pairs and F-only codes — these almost always need a technician
Drain time is longer than expected — typically over eight minutes.
Washer is sensing low flow or taking too long to fill.
The main control senses water level exceeding the washer's capacity.
The basket speed sensor detects the target RPM was not reached.
The door is not locking properly, so the washer won't start.
The motor cannot achieve the correct speed for the cycle.
There is a problem with the dispenser system.
The hot and cold water inlet hoses are installed the wrong way around.
The sensor detecting detergent level in the Load & Go™ dispenser has failed.
The door can't lock — the lock assembly has failed or the wiring harness is damaged.
On Whirlpool VMW top-load models, the main control has lost track of basket rotation.
The lid is not locking on top-load models.
The washer is not draining properly on models that display word codes.
no technician needed in most cases
Too many suds in the drum, so the washer extends rinse time to flush them out.
The load is unevenly distributed in the drum.
The washer load was too large.
Hot and cold water inlet hoses are connected the wrong way around.
The washer lid was left open on a top-load model.
The cycle was interrupted by a power failure.
The cycle was paused or cancelled.
Control Lock has been activated.
Items were detected in the washer during the Clean Washer cycle.
The detergent cartridge is not detected in the Load & Go™ dispenser.
Additional codes like F0 E0, F1 E1, F2 E1, F6 E1, F6 E2, F6 E3, F9 E2, F9 E3, F0 E5, F0 E1, F7 E5, F7 E6, F8 E4, F3 E1, F3 E2, F3 E3, Sd, Po, and any other code your Whirlpool washer displays — all are diagnosed accurately to find the root cause.
Didn't find your error code? Call 054 400 6384.
Whirlpool washers aren't like any other machine. Their 6th Sense load detection, SenseInverter motors, and FreshCare+ steam systems are advanced — and we've been working on them daily.
Detects the type and weight of each load and automatically chooses the optimal wash parameters. Intelligent sensors recognize load size and fabric type, adapting water temperature, water level, and drum movements automatically for up to 50% energy and water savings. We diagnose and repair the sensors, control board, and load detection components that manage this system.
Highly efficient, delivering up to 30% energy savings compared to A+++ performance. This brushless motor provides powerful, quiet, and energy-efficient operation. We diagnose and repair motor control modules and replace faulty inverter boards.
Prevents bacteria growth inside the washer for up to 6 hours after the wash ends. It uses steam directly injected into the drum, combined with gentle bidirectional drum movements, to keep garments fresh and prevent creases. Awarded the Allergy UK seal of approval and proven to alleviate 99.9% of major allergens including dust mites, pollen, and pet dander. We service steam generators, water lines, and heating elements.
Lets you skip adding detergent to every load. The system holds enough detergent for multiple loads and automatically dispenses the right amount at the right time. Available on select front-load and top-load models. We repair dispensing pumps, level sensors, and the auto-dose control board. Common F3 E4 error codes relate to the detergent level sensor in this system.
Lets you soak, scrub, and wash all in one spot. It includes a built-in dual-temperature faucet and a stain brush for spot-treating stains directly in the washer. Available on select top-load models including WTW6120H. We service the faucet assembly, water supply components, and related control board systems.
Provides up to six tailored drum movements for extraordinary wash results — Steam Massage, Energetic Wash, Wave Motion, Slow Motion, Shower Tumble, Color Bath, and Cradle Motion. Each movement is pre-set for specific fabric types and wash phases. We diagnose and repair the motor control and drum movement systems that manage these cycles.
Allows you to customize the wash cycle based on your needs, choosing from 3 different levels of cleaning intensity to remove all types of dirt from your laundry. We diagnose and repair the control board and cycle selection components that manage this function.
Control and monitor your washer via the Whirlpool app. Receive real-time completion notifications and manage your laundry from anywhere. We diagnose and repair connectivity issues, Wi-Fi module faults, and control board problems affecting the smart system.
Whirlpool's direct-drive top-load washers use a motor directly coupled to the transmission, eliminating belts and pulleys for quieter operation and greater durability. The plastic drive coupler in these machines is a known wear item at year 5–10. We repair or replace drive couplers, motor couplings, and related components.
Keeps even oversized loads balanced for smooth, quiet operation. We repair suspension systems, shock absorbers, and leveling issues that cause excess vibration during the spin cycle.
On models like WFW5720R, this system uses a fan to periodically tumble clothes for up to 12 hours after the wash cycle ends, keeping loads fresh if you can't move them to the dryer right away. We service the fan motor, vent system, and control components.
Uses sensors to adapt the wash cycle in real time based on soil level, fabric type, and load size. We diagnose and repair the sensor array, control board, and load detection components that manage this adaptive system.
Pick the symptom closest to your situation — each one walks you through what usually causes it and how we fix it.
Water left standing after the cycle? The most common cause is a clogged drain-pump filter or coin trap — often a free fix. We clean the filter, check the drain hose for kinks, and replace the drain pump if needed.
Learn moreWasher won't fill? Check if the water tap is open, the inlet hose is kinked, or the water supply filter is clogged. Both hot and cold must be connected and open — Whirlpool washers need pressure from both hoses for the valve to operate.
Learn moreClothes coming out soaked? Whirlpool washers fail to spin from five common causes: failed door-lock switch, worn drive belt or stripped drive coupler, failed shifter actuator on Cabrio/VMW, clogged drain aborting spin, or a failed motor control unit.
Learn moreBanging, grinding or squealing during spin? On Whirlpool top-loaders, noisy almost always starts with outer tub bearing wear on the VMW platform. A drum that rumbles on spin or shows play at the rim is a bearing and tub-seal question. We diagnose and replace the specific worn component.
Learn moreWater on the laundry room floor? Common causes include a loose water supply hose connection, a misaligned drain filter, or a worn door seal. We find the source and fix it fast.
Learn moreMachine moving during spin? On top-loaders, heavy vibration usually means the four suspension rods that hang the tub have worn springs. We replace suspension rods, shock absorbers, and level the machine.
Learn moreNo power at all? We check the power supply, control board, and door lock mechanism. Quick reset: unplug the washer for 5 minutes to clear glitches, then plug it back in.
Learn moreA cycle stalling at drain, a spin that never reaches speed, or a door that won't unlock. We diagnose the drain pump, filter, door lock assembly, pressure switch, and motor control — in that order.
Learn moreMusty odors from the drum? Common on front-load models. We clean and replace moldy door gaskets and address drainage issues causing bacteria buildup. We recommend regular Clean Washer cycles with affresh tablets.
Learn moreThe Load & Go system may be disabled, the dispenser may be clogged, or the detergent level sensor may have failed. Pull the cartridge straight out, rinse it and the cavity in warm water, and brush the dispensing ports clean. We diagnose and repair dispensing pumps and level sensors.
Learn moreWhether your washer is a top-load 6th Sense or a premium front-load Load & Go™ model, our technicians are trained on every platform.
4.5 cu. ft. 12 cycles, 25-minute Quick Wash. Common issues include F9 E1 drain errors and drain pump bearing failure.
Front-Load · Entry4.3 cu. ft. closet-depth fit, Intuitive Controls, 35 cycle combinations. Common issues include F8 E1 long fill errors and door lock failures.
Mid-RangeFreshFlow™ Vent System, 12-hr FanFresh® Option, AI Intelligent Wash, Steam Clean Option. Common issues include F5 E2 door lock errors and control board faults.
Mid-Range Plus5.0 cu. ft. Common issues include F9 E1 drain errors and motor control board failures.
PremiumLoad & Go™ XL Dispenser, Wash & Dry Option, ADA Compliant. Common issues include F3 E4 Load & Go dispenser errors and F9 E1 drain errors.
Premium PlusSmart Capable, 37+ cycle combinations, Load & Go™ XL Dispenser. Common issues include F3 E4 dispenser errors, F9 E1 drain errors, and Wi-Fi module faults.
Top of Line4.5–4.6 cu. ft. capacity, built-in water faucet, presoak option, deep water wash option. Common issues include lid lock failures and F8 E1 long fill errors.
Top-Load · Entry4.7–4.8 cu. ft. flexible capacity, 2-in-1 Removable Agitator (industry-first), EasyView™ Slow-Close Glass Lid. Common issues include shifter actuator failure and drive coupler wear.
Mid-Range4.8 cu. ft. capacity, Pretreat Station Plus with built-in dual-temperature faucet and stain brush, Load & Go™ dispenser. Common issues include lid lock failures and F7 E7 motor speed errors.
Smart Capable6.0 cu. ft. capacity, 2-in-1 Removable Agitator, Smart Capable, Load & Go™ dispenser. Common issues include F9 E1 drain errors and shifter actuator failure.
6.0 cu. ft.Whirlpool's classic front-load platform. Common issues include drain pump failure, drive belt wear, tub bearing failure (3–4 hour labor job), and door lock assembly faults. On a Duet under, a confirmed bearing failure is usually worth repairing — you buy 5–8 more years.
Legacy PlatformWhirlpool's vertical modular washer platform. Common issues include failed shifter actuator, worn drive coupler, and bearing wear. The drive coupler strips at year 5–10. Cabrio top-load access is simpler and cheaper than Duet front-load for bearing replacement.
Legacy PlatformDon't see your model? Call us — we likely service it.
Because a Whirlpool isn't just any washer. Its 6th Sense load detection, SenseInverter motor, and FreshCare+ steam systems are advanced. We've worked on them daily.
No waiting rooms, no hauling your machine across town, no surprise invoices.
Tell us your Whirlpool model and the error code or symptom. often 60 to 90 minutes.
Most Whirlpool codes have several possible causes — and the cheapest one is often the real one.
Most repairs are completed on the spot with Suitable parts.
Our technicians cover Dammam, Al Khobar and Dhahran.
The things customers in Dammam most often ask us before booking a Whirlpool repair.
F9 E1 means long drain — drain time is longer than expected, typically over eight minutes. The most common cause is a clogged drain pump filter or coin trap. Other causes include a kinked drain hose or a failing drain pump.
F8 E1 means long fill — the washer is sensing low water flow or taking too long to fill. Check that household water supply is turned on and both hot and cold valves are fully open. Inlet hoses should not be kinked. The water inlet valve screen may be clogged. Water pressure must be at least 10 psi.
The origin is usually a clogged drain pump filter, a kinked drain hose, or a failing drain pump. Same repair path as F9 E1.
F5 E2 means the door is not locking properly. Check that nothing is blocking the door and that it is fully closed. The door lock assembly may need replacement — we repair or replace the lock.
F3 E4 relates to the detergent level sensor in the Load & Go™ Dispenser. Clean the dispenser cartridge and cavity thoroughly. If the code persists, the level sensor may have failed and needs replacement.
In almost every case, yes. Whirlpool washers are built to last 10–. If your machine is under 8 years old and the repair costs less than half the price of a new one, repair is almost always the wiser choice.
Yes. Our technicians are trained on Whirlpool's 6th Sense Technology and can service the load detection sensors, control board, and related components. We also service the SenseInverter motor, FreshCare+ steam system, Load & Go™ dispenser, and SoftMove drum movement systems.
Yes. Load & Go™ problems usually show up as F3 E4 or dET. We clean the level sensor and dispenser cavity, replace the sensor if it has failed, and repair the dispensing pump if needed. Most Load & Go repairs are completed on the same visit.
Tell us the symptom or error code and we'll route you to the right Whirlpool specialist. Call now Call us for the earliest visit slot, or send your details and we'll call you back as soon as possible — calls answered 24/7.